Notes on project Gamma - The RF Deck

Introduction and commentary

One would think, if one didn't know anything about solid state amplifiers (and I don't, or at least didn't), that this would be the hard part. In a tube amp, the RF deck is the easy part. There are only a few components (tube, socket, input choke), they are fairly easy to understand, and quite robust (both mechanically and electrically). But with a solid state amplifier, this just isn't true. Transistors are very finicky. Designing a new solid state RF deck is hard. Luckily, it turns out that you don't have to design a new RF deck! A very capable RF engineer at Motorola named Helge Granberg did the heavy lifting about 20 years ago, and wrote it all down for us in a series of application notes and engineering bulletins. Even if you don't want to use Motorola parts (or, to be more precise MA-COM parts - since they now have the rights to the old Motorola transistors), you can still use the bias circuitry, board layout and input/output circuitry from those old Motorola documents.

So the question on the RF deck boils down to a fairly easy set of questions:

1. Do you want to use Motorola parts or not?
2. If no, which parts are you going to use, and how are you going to get the boards designed?
3. If yes, which part ? The obvious choices are the MRF-150 or the MRF-154.

My sense after some discussion and thought is that the answer to the first question is "yes". Even though the MRF-150/151/154/157 design is an old one, it still offers the best performance in several dimensions. First, and perhaps most importantly, these parts have the best IMD characteristics and linearity of any commonly available HF amplifier. Second, the board designs are done, and tested, and have been proven in battle. Third, 48 volt DC power supplies are available used a good prices, which isn's true for the higher voltages required by some alternative parts.

On the third question then, the real issue is this: do you use MRF-150's (150 watts each, requiring either 12 or 16 transistors for our project), or MRF-154/157's (600 watts each, requiring 4 for our project)? Despite the obvious benefits of using the MRF-154's (only two boards and many fewer parts required, and simpler splitter/combiner), the collective wisdom of the solid state crowd seems to be in favor of the smaller parts. The issue that everyone talks about is heat. Apparently, the MRF-154 has major heat management issues. You are making a lot more heat in a small space - getting that heat into a heat sink under contest conditions is apparently quite difficult. I think that if you are willing to go with a water cooled design, using the MRF-154 would be ok - but if you want an air cooled design, sticking with the MRF-150's makes more sense.

There is also a secondary issue of cost. Because the MRF-154's are much less frequently used, they are much more expensive. MRF-150's can be had today for $188 for a matched quad (see below). Advanced Power Technology is about to releast their plug compatible VRF-150 (parts should be available in Q1, 2005), and they are quoting $38 each in quantity 5000.

MRF-154's on the other hand, are hard to find and priced at over $850 per pair. So even if our design uses 16 MRF-150's (we may get away with 12, but that is a subject for later), and even if we pay the current price of $188 per quad, our power transistors will cost $752. Four MRF-154's will cost us the princely sum of $1,700 - and if we blow one up we will be sad indeed.

Notes and commentary

Communications Concepts makes and sells boards and parts kits based on various Motorola application notes. It appears that either the board based on the EB104 (600 watts, 4 x MRF150 ) or the board based on AR347 (1000 watts, 2 x MRF154) would be the best bet.

A potentially interesting source for MRF-150's is:

-----Original Message-----
From: David Gilden [mailto:David.Gilden@rfmw.com]
Sent: Tuesday, January 04, 2005 8:31 AM

We can supply the MRF150 in any fashion you wish.

Singles units are $41.00 each

Matched Pairs are $88.00 each ( 2 transistors)

Matched quads are $188.00 each (4 transistors)

David Gilden

RFMW, Ltd/RF Power Exchange
-------------------

Notes: Sand Labs makes RF boards (and possible power supplies). http://www.sandlabs.com/pa.htmlunder products/RF